After working for whole day excavator stops work, the hydraulic fluid  is in  high temperature, the air outside  is in low temperature, in outside fuel tank's hot air and fuel tank's cold air meet contact, coldly will condense the water-drop whereabouts in fuel tank's crown in the hydraulic fluid, gradually, in the hydraulic fluid will mix in the water. Subsequently evolves the acidification material dipping surface. In the mechanical operation and under the pipeline pressure impact's dual function, the metal pellet which the metal surface will fall off down will mix in the hydraulic fluid, if this time the hydraulic fluid will not make the cleaning treatment big metal pellet to filter by the filter element, but will be smaller than 10μm the pellet hydraulic pressure filter element cannot filter, will not be able to filter the attrition pellet mix will aggravate the metal surface in the hydraulic fluid the attrition once more, therefore the expert suggested that the hydraulic fluid filtration purification time will be 2000-2500 hours or 1 year purifies one time, when trade the fresh oil must purify one time. After the old oil purification in the system, changes the fresh oil,  replenishment with fresh oil, such residual old oil will not pollute the fresh oil.
The best measure, regularly purify the oil with the hydraulic fluid special-purpose vacuum oil filter machine, process the unnecessary moisture content and the mechanical impurity, and  maintains the cleanliness at NAS6-8 level, the moisture content in the GB code scope, the control oil quality is not easy to get older, like this unearths the equipment not to be easy to damage and the fat liquor is durable, help avoid losing and  waste!

Hydraulic cylinder for mould in HC hydraulic cylinder Co.,Ltd,is change the hydraulic energy to be the mechanical energy,do linear reciprocating motion (or swinging movements) of the hydraulic actuators.

Hydraulic cylinder for mould structure is simple and reliable.Using the Hydraulic cylinder for mould to realize the reciprocating motion, can discharge the deceleration device, and no transmission clearance, smooth movement.So in all kinds of hydraulic cylinder for mould system widely used.

The hydraulic cylinder for mould output force and the piston area is directly proportional to their effective on both sides of the pressure difference; basically,Hydraulic cylinder for mould consist of cylinder and the cylinder head , piston and piston rod seals and sealing devices, buffer device and exhaust device component. Buffer device and exhaust device according to specific applications and decide, other devices is indispensable.

 

We have a group of senior enginners who commit ourselves to designing and manufacturing in the hydraulic cylinder for mould and devote ourselves mind to improving and researching of products.Hydraulic cylinder for mould

Keep improving for your hydraulic cylinder for mould,precise quality management and diversified testing so that we can keep excellent quality and be admitted for the same line of business.Hydraulic cylinder for mould.
If you are interested in our hydraulic cylinder for mould,welcome to contact me.

Contact person:Tina
Skype:anole-01
service1003@hc-hydraulic-cylinder.com

From 2000 year, HC has operated many types of hydraulic cylinders. Here I’d like to summarize them.

The most popular hydraulic cylinders: double-acting hydraulic cylinders. Double-acting hydraulic cylinders have many series as follows: square hydraulic cylinder, round hydraulic cylinder, light hydraulic cylinder, heavy hydraulic cylinder, self-locking hydraulic cylinder, proximity switches cylinder, metallurgical equipment cylinder and Custom hydraulic cylinder.

We also sold a large number of single-acting hydraulic cylinders in 10 years. The most hydraulic cylinders dimensions are according to buyers’ requests.

In 10 years, HC Hydraulic Cylinder Co., Ltd has our own designing standards for different sizes of hydraulic cylinders.

There are two main designing methods:

1.    Draw bar hydraulic cylinder: this type hydraulic cylinder is widely used in industry factories. Small cylinder barrel always have 4 screws but large cylinder barrel may need 16-20. People can separate the hydraulic cylinder if broke down.

2.    Welded hydraulic cylinder: there is no screw in welded hydraulic cylinder, the cylinder barrel and bottom welded together, the same as glib. The former rod cap is always across or connected to cylinder barrel by screw. In this way, user can separate the piston, rod and seals directly.

Welded hydraulic cylinders have many advantages than draw bar hydraulic cylinders. This cylinder barrel usually narrower and length is shorter, so it makes machine spare parts connection much easier. In addition, because there is no tie rod, it won’t appear the phenomenon that caused by tie rod break down in high pressure or stroke is too long condition.

Due to welded hydraulic cylinders’ surface is very smooth, and are good ways to design multi-stage hydraulic cylinders. Welded hydraulic cylinders are widely used in every field. For example, construction equipment (excavators, bulldozers and graders), cargo equipment (truck, lift gate) and heavy-industry equipment (crane, oil rig, ORV) and so on.

 

 

 

 

1. the heading - prerequisite decides the seal institute in the position heading, for example reciprocation, revolving, screw or fixed. 　　
2. the seal key - for example decision spot is seals or the active spot in the inside diameter tension bar is seals and so on the outer diameter piston. 　　
3. the temperature rank - from the original factory machinery operating instructions consult or according to the practical work environment appraisal operating temperature, decided that must use the material. Related temperature rank's showing may refer to the following production user matters needing attention. 　　
4. the pressure rating - from the original factory machinery operating instructions consult related data, or through observes original seal soft degree of hardness and the structure inference working pressure rank, related pressure rating's showing may refer to the following production user matters needing attention. 　　
5. the size dimension - most users can according to having used the old sample select and purchase, but seal after using period of time, by factors and so on temperature, pressure and attrition affects largely its original size, will choose according to sample can only take a reference, a better method will measure the seal institute in the positionThe metal trough size, the accuracy will be high.

The hydraulic ram, people pay little note about it  in the automobile, the agriculture machine and so on motor vehicle's small spare part, however it  is precisely small fitting, actually becomes modern of  pillar industry. 　　
The hydraulic cylinder is one kind of implementing agency. The hydrauliccylinder generally by the cylinder body, the cylinder pole (connecting rod) and the seal is composed, the cylinder body interior divides into two parts by the piston, passes an oil hole separately. Because the liquid compression ratio is very small, when therefore an oil hole enters time the oil, the piston will be impelled to enable another oil hole to leave the oil, the piston leads the connecting rod to do stretches out (retracts) the movement, otherwise still. 　　
Hydraulic transmission principle: Takes the actuating medium by the fat liquor, transmits the movement through the seal volume's change, transmits the power through the fat liquor internal pressure. 　　
1st, power section: Transforms prime mover's mechanical energy for the fat liquor pressure energy (hydraulic pressure can). For example: Hydraulic pump. 　　
2nd, operative paragraph: Transforms the hydraulic pump input's fat liquor pressure energy to lead the operating mechanism the mechanical energy. For example: Hydraulic ram, oil motor. 　　
3rd, control section: Uses for to control and the adjustment fat liquor pressure, the current capacity and the flow direction. For example: Pressure control valve, flow control valve and direction control valve. 　　
4th, auxiliary body: Front three parts will connect in together, composes a system, plays stores roles and so on oil, filtration, survey and seal. For example: Pipeline and attachment, fuel tank, filter, accumulator, seal and control instrument and so on. 　　
The hydraulic ram principle of work the pressure which a spot exerts willfully on certain volume's liquid, can the size equally to each direction transmission. This means that when uses many hydraulic rams, each hydraulic ram will pull according to the respective speed or pushes, but these speeds are decided the pressure which needs in the motion load. In the hydraulic ram bearing capacity scope same situation, the load bearing minimum load's hydraulic ram will first move, the load bearing biggest load's hydraulic ram will move finally. In order to cause the hydraulic ram synchronization movement, achieves the load to go against in any spot by the identical speed rises, certainly must use the control valve or the synchronization in the system goes against rises the system element.